Using CloneZilla with Software RAID5. Ask Question 0. I'd like to image my software RAID5 configuration (3 drives), then move it to a new set of hard drives. Since CloneZilla doesn't support software RAID, I was hoping to do the following: Create an image of each device using CloneZilla on an external HDD (from.
Clonezilla Downloads Windows 10
What RAID cards does Clonezilla support?? 0 Thai Pepper. With the software raid in Linux you can pull the drives from one system, put them in another Linux system and still be able to use the array. How can you clone (copy) drives from a RAID 0 array. I have an XP desktop that currently has 2 - 1 TB WD Caviar Black drives in it. One of the drives seems to have started failing as it has. Raid 0 is just another drive.I use Acronis true image,Its reliable and will also clone large to smaller drive auto resizing the partition in the process.Theres also clonezilla and macrium reflect which are free. Would it be possible to add support for firmware RAID devices? In this case I have an Intel RST RAID 1 which appears in /dev/mapper. I'm using Clonezilla 2.6.0-37. In the BIOS, I configure Intel RST as RAID 1 called Volume0. Create a Project Open Source Software Business Software Top Downloaded Projects. Blog @sourceforge Resources.
Situation:
- One empty 120GB SSD
- Two 60GB SSD's is RAID 0 containing a Windows 7 installation
- The RAID is firmware-based (a.k.a. fakeRAID) which means it requires a driver for it to be seen by an operating system.
I don't want to use RAID 0 anymore; far too dangerous. I want to take the data from the RAID array and put it onto the single 120GB SSD. Ultimately, I want to keep the Windows 7 install completely intact; I don't want to reinstall anything.
Keep in mind I have multiple TB worth of free space to use as temporary storage for whatever transfers need to take place.
I looked into Clonezilla but it (as with most cloning software) doesn't support firmware-based RAID.
Raystafarian2 Answers
Try EaseUS Disk Copy utility to clone a RAID 0 array to a single disk.
Raystafarian
cpuguruClonezilla Software Raid 0 Xp 10
Download and install the excellent (and free!) Paragon Backup.
Do a FULL backup using Windows backup. You can store it on a 3rd hard disk, or USB drive or even another computer on your network. I used a networked computer. This is our emergency only, last resort, in case all else fails backup and will not be used if all goes well. Make the recovery disk when prompted. As a further precaution boot into the recovery disk and ensure you can access the backup. Do not skip this step!
Now do a FULL backup using Paragon Backup. Same location if you like (this is the one we will restore later). Make sure you backup the MBR, System Reserved (~100MB) and windows partitions. Minimum 3 ‘partitions’. If that’s all you have then fine, just make sure you backup ALL your partitions. The MBR is not, strictly speaking, a partition but you will see it listed.
Create the Paragon backup/restore CD or USB (I used a USB thumb)
Boot the Paragon backup/restore disk you created in step 4, and make sure you can access the backup you created in step 3, If you used the network like me, then you will need to set it up using the ‘Configure network’ option. If you cannot access the backup then you will need to move the backup. Just make sure you can access the backup using the Paragon backup/restore disk before you continue.
Reboot and enter your RAID BIOS, destroy your array, do not create a new array.
Boot the Paragon backup/restore, now restore your backup of windows 7 to disk 0. Make sure to restore the MBR and the ~100MB ‘System Reserved’ partitions as well as the windows partition.
Once completed you should now be able to boot into windows.
Open ‘Device Manager’ and look for your RAID driver. Uninstall it. You should be prompted to reboot.
Enter your Mainboard BIOS setup, Change the sata controller mode from RAID to SATA (you could try AHCI but if it wont boot you will need to follow one of the many guides on enabling AHCI).
If all went well your done, windows will install the correct drivers for your sata controller and want to reboot again most likely, but basically that’s it.
For more details, please check out this blog entry I have written on the subject.
JakeGould